MEP SYLLABUS

• Heating Ventilation and Air Conditioning (HVAC)
• Electrical Design and Drafting
• Plumbing Design and Drafting
• Fire Fighting and Drafting
• Revit MEP

1.HVAC - HEATING VENTILATION AND AIR CONDITIONING TRAINING

1. INTRODUCTION


2. HEAT

   Types of Heat:

   1. Sensible Heat
   2. Latent Heat
    

   Mode of Heat Transfer:

   1. Conduction
   2. Convection
   3. Radiation
 
3. VENTILATION
   1. Introduction
   2. Calculation of CFM
   3. Calculation of ACPH
   4. Calculation of CMH
   5. Types of Ventilation
   6. Positive Pressure
   7. Negative Pressure
   8. Types of Ventilation Fans
 
4. AIR-CONDITIONING
   1. Properties of Air
   2. Dry bulb Temperature
   3. Wet bulb Temperature
   4. Relative Humidity
   5. Dew Point Temperature
   6. Ton of Refrigeration
 
5. TYPES OF AIR-CONDITIONING

   Direct System:

   1. Window AC
   2. Split AC
   3. VRF System
    

   Indirect System:

   1. Air Handling Unit
   2. Fan Coin Unit
   3. Chilled Water System
 
6. HEAT LOAD CALCULATION
   1. Glass
   2. Wall
   3. Roof & Floor
   4. Partition
   5. Ceiling
   6. Lighting
   7. Electronics Equipment
   8. Occupancy
 
7. SELECTION OF INDOOR & OUTDOOR UNITS
 
8. AIR TERMINAL SYSTEM
   1. Diffuser
   2. Types of diffuser
   3. Calculation of neck size
   4. Placement of diffuser
   5. Grill
   6. Calculation of size of grill
   7. Types of grill
 
9. AIR DISTRIBUTION SYSTEM
   1. Duct
   2. Types of duct
   3. Designing of duct
   4. Flexible Duct
   5. Plenum Box
   6. Calculation of size of plenum box
 
10. AIR DISTRIBUTION SYSTEM
    1. Chiller
    2. Cooling Tower
    3. Pipe Design
    4. GPM Calculation
    5. Pump Head Calculation
 
11. BILL OF QUANTITY PREPARATION
 
12. DUCT MATERIAL CALCULATION
 
13. PIPE MATERIAL CALCULATION
 
14. STATIC PRESSURE CALCULATION
 
15. SPECIFICATION OH HVAC
 
16. SUPPORT AND ACCESSORIES IN HVAC
 
17. TESTING AND COMMISSIONING
 
18. SOFTWARE
    1. Auto cadd - 2D Design
    2. Mc - quay duct sizer
    3. Mc - quay pipe sizer
    4. Heat Load Excel Sheet
    5. Cooling Load Calculation
    6. HAP
 
19. REVIT -3D DESIGN
 
20. FINAL PROJECT

2. ELECTRICAL DESIGNING & DRAFTING SYLLABUS

1.GENERAL CONCEPT :

1. Electrical Generation, Transmission and Distribution
2. Different types of equipment and their load as per standard specifications
3. Services : Lighting, Power, Fire Alarm, Emergency Lighting, etc

2.SYMBOLS AND LEGENDS :

1. Power Services
2. Lighting
3. Fire Detection
4. ELV/ Low Current
5. Earthing and Lighting

3.POWER SERVICES :

1. Cables
2. Selection, Conductor, Strands, Cores and Insulation
3. Armored and Unarmored Cables
4. Cable tray raceway, Trunking, Conduits and Routing
5. Busbar Details and selection of high rise building
6. Switch Gears (Circuit Breakers) Types and Selection
7. Capacitor bank (Power factor improvement)
8. Panel Boards (MDB, SMDB, SDB, etc)
9. Single line Diagram (SLD)
10. Calculation: Voltage drop calculation and load calculation based on BS 7671

4.LIGHTING :

1. Lux level design as per BS 12464
2. Escape route lighting as per NFPA 101
3. Different types of Lamp like GSL, ETL, CFL, LED, MVL, etc

5.FIRE DETECTION :

1. Fire alarm system as per NFPA 72
2. Smoke (Heat Detection)
3. Sounders & Manual call points
4. Voice evacuation system for commercial / Residential building

6.ELV / Low Current system: (General Concepts) :

1. Public Address System
2. Close circuit television (CCTV): Types of cameras and circuiting
3. Communication: TV, Telephone, intercom and internet networking of cables and types

7.Earthing and Lighting :

1. Lighting Protection
2. Introduction to Lightning Arresters
3. Lightning protection system design based on BS/IEC 62305
4. Types of Earthing According to the requirements
5. Earthing system design in line with BS 7430

8.TYPES 0F DRAWING: DESIGN DRAWING AND SHOP DRAWING :

9.DRAWING DETAILS :

1. Lighting Layout
2. Power Layout
3. Emergency Lighting Layout
4. CCTV Layout
5. Public Addressable Layout
6. Fire Alarm system Layout
7. Communication Layout
8. Cable Tray Layout
9. BUSBAR Layout
10. Bus duct riser drawings
11. Single line drawing (SLD)

10.STANDARD & CODES :

1. Designing as per Electrical standards: DEWA, ADEWA, ADDC, KHARAMA, etc

11.PROJECT :

1. Lighting Layout
2. Power Layout
3. Single line drawing (SLD)
4. FA, PAVA, Emergency Lighting Layout
5. Communication layout
6. ELV system (CCTV, ACS, etc)

3. PLUMBING DESIGNING SYLLABUS

CERTIFICATE IN PLUMBING DESIGNING

COURSE DESCRIPTION:

PLUMBING SYSTEM DESIGN - LEVEL 01

Learn the fundamentals of pressurized water distribution systems for commercial and residential high - rise buildings, Topics include pressure flow equations, friction, mechanical pumping, cold water distribution, backflow prevention, applicable codes and their use, and system selection.

PLUMBING SYSTEM DESIGN - LEVEL 02

Understand the fundamentals of sanitary and storm drainage system design for commercial and residential high - rise building. This course includes coverage of laboratory healthcare acid waste and drainage systems: piping materials: hangers and storm flow: venting: indirect waste: laboratory waste: piping materials: hangers and supports for drainage piping: ejector and sump pump design: site drainage design: storm water detention systems: grease, oil, and sediment interceptors: and acid waste neutralization. Gain an overview of advanced technologies related to sanitary and storm water system, such as grey water and black water system and storm water reuse systems and filtration.

AFTER COMPLETION OF THE PROGRAM, STUDENTS ARE SKILLED IN THE FOLLOWING AREAS

• Pressurized water distribution systems
• Water chemistry and treatment
• Hot and cold water distribution
• Valves and fixture
• Nature gas distribution
• Building drainage system
• Storm water drainage
• Sanitary waste disposal

4. FIRE FIGHTING SYLLABUS

FIRE FIGHTING COURSE PLAN

1.BASISCS OF FIRE FIGHTING :

• Basics of fire fighting
• Fire fighting standards
• Fire fighting pipe materials
• Fire legends

2.EXPLANATIONS OF NFPA CODES :

• Overview of NFPA 10
• Overview of NFPA 13
• Overview of NFPA 14
• Overview of NFPA 20
• Overview of NFPA 22

3.FIRE PROTECTION SYSTEM :

• Active fire protection system
• Passive fire protection system

4.CLASSIFICATION OF FIRE :

• Classification of occupancies
• Classification of commodity

5.DESCRIPTION OF FIRE HAZARDS :

• Description of fire hazards
• Classification of hazards
• Detailed explanation of hazards

6.TYPES OF SPRINKLER SYSTEM :

• Types of sprinkler system
• Explanation of Wet sprinkler system
• Explanation of Dry sprinkler system
• Explanation of Pre - Action sprinkler system
• Explanation of Automatic sprinkler system

7.DESCRIPTION OF SPRINKLER AND HOSE SYSTEM :

• Sprinkler system explanation
• Types of sprinkler
• Selection of sprinkler
• Hose reel system

8.FIRE EXITNGUSHERS DETAILS AND ARRANGEMENTS :

• Types of extinguishers
• Arrangements of fire extinguishers
• Applications of fire extinguishers

9.DETAILS & DESIGN OF ZONE CONTROL VALVE :

• Description of zone control valve
• Design of zone control valve

10.FIRE FIGHTING DESIGN CRITERIA :

• Sprinkler design
• Sprinkler arrangements
• Pipe sizes

11.DESIGN OF FIRE SUPPRESSION SYSTEM :

• Design of fire suppression system

12.EXTERNAL FIRE FIGHTING DESIGN :

• Design of Fire Hydrants
• Design of Breaching Inlet

13.DESCRIPTION OF FIRE PUMPS :

• Detailed description of fire pumps
• Types of pump

14.FIRE PUMP ROOM DETAIL :

• Fire pump installation details
• Fire equipments design
• Fire pump rooms line sketch
• Pipe and equipments support details

15.FIRE PUMP CALCULATION :

• Pump head calculations

16.FIRE FIGHTING HYDRAULIC CALCULATION :

• Hydraulic calculation

17.FIRE FIGHTING TECHNIQUIES :

• Site photos presentation
• Establishments of new creativities
• Fire Fighting techniques

18.DESCRIPTION OF FIRE FIGHTING LAYOUTS :

• Detail description of design drawings
• Detail description of shop drawings

19.LAYOUT PREPARATION PROCEDURES :

• Design drawing preparation procedures
• Shop drawing preparation procedures

20.GENERAL DRAWING PREPARATION PROCEDURES :

• Schematic drawing preparation procedures
• Shop drawing preparation procedures
• Sectional layouts preparations
• Bill of Quantity preparations

21.PROJECT :

• Commercial Building Fire Fighting Design
• Residential Building Fire Fighting Design
• Airport Fire Fighting Design
• Hospital Building Fire Fighting Design

5. REVIT MEP SYLLABUS

• Building information Modeling
• Building information Modeling(BIM)
• Revit MEP Basics Overview of the interface
• Standard Terminology
• Starting Projects
• Viewing Commands Basics Drawing & Editing Tools
• General Drawing Tools
• Editing Elements
• Standard Modifying Tools
• Helpful Editing Tools
• Starting MEP Projects
• Linking in Architectural Projects
• Introduction to Architecture
• Copying & Monitoring Objects
• Setting Up Levels
• Working with Views
• Duplicating Views
• Adding Callout Views
• Setting The View Display
• Creating Elevations
• Creating Sections
• Working With Ceilings
• Understanding Revit
• MEP Systems
• Working with Schedules
• Creating Schedules
• Working with Dimensions
• Working with Text
• Adding Detail Lines & Symbols
• Creating Legends
• Tag & Schedules
• Adding Tags
• Detailing in Autodesk
• About MEP Systems
• HVAC Systems
• About HVAC System
• Adding Air Terminals & Mechanical Equipment
• Adding Ductwork
• Creating Duct Systems
• Automatic Ductwork Layouts

Practice

• Working With Components
• Creating Systems - Overview
• System Graphics
• Connecting Components
• Analyzing Systems
• Spaces and Zones
• Creating Spaces
• Working with Spaces
• Creating Zones
• Creating Color Schemes
• Performance Analysis
• Preparing a Project for Energy Analysis
• Analyzing the Heating & Cooling Loads

PIPING SYSTEM

• Hydronic Piping
• Systems
• About Hydronic Piping Systems
• Adding Mechanical Equipment
• Drawing Piping
• Creating Hydronic System
• Automatic Piping Layouts
• Visibility Graphic
• Creation Of Pipes
• Practice
• Fire Production Systems
• Plumbing Systems
• About Plumbing Systems
• Adding Plumbing Fixtures
• Drawing Piping For Plumbing Systems
• Working With Plumbing Systems
• Electrical system
• About Electrical system
• Placing Electrical components
• Creating Electrical circuits
• Cable trays and conduit
• Electrical panel Schedules
• Family creation
• Family creation

LAYOUTS

TOPICS :

• Construction documents phase
• Construction
• Documents
• Setting up sheets
• Placing & modifying views on sheets
• Adding revisions
• Printing sheets
• Work sharing